Brainwave frequencies are in the range of 0.1 to 4 (Delta), 4 to 7 (Theta), 7 to 13 (Alpha) and 13 to 30 (Beta) cycles per second (Hz). Brainwave entrainement (or synchronization), aims to cause our brainwave frequencies to fall into step with a periodic stimulus having a frequency corresponding to the intended brain-state. Scalar energy healing frequency 432 Hz - scalar wave generator USB plugin - scalar wave technology for health and scalar healing 818-478-9283 info@qummulator.com 0 items $0.00. Remains until 28 mins, and then steps up 2 Hz per minute to finish at 10 Hz. Instrumentation: Tuned to 432 Hz to provide an increased sense of well-being and connectedness to the present moment. Frequency: Starts at 12 Hz and ramps down 3 Hz per minute to 9 Hz. Stays at 9 Hz for 7 minutes.
How to make a Frequency Generator:
On cloud busters Fredbuster created awonder tutorial for getting started and building your own Zapper. Fredbusters Tutorial in PDF-Basedoff his design here is how I made my frequency generator.
The Fredbuster's circuit layout
The Circuit design I use to create a variable frequencygenerator.
What you will need:
1 Project box with PC board included,
1 Compositor 1 micro farad, C2, I like the un-polarized becauseit allows you not to worry about positive an negativesides. If you do get one with a longer leg that's the positive, see schematicfor proper placement.
1 Compositor .01 micro farad, C1
1 LED 1-3 volt, small red ones. Remember the longerleg is the positive, connect properly,
1 Resistor 3.3k ohm, R1, It will say it on the upper partfiguring out the colors is a pain. See photo below for product ID.
1 Resistor 3.9k ohm R4
432 Hz Generator
1 Resistor 4.7k ohm R5
1 Resistor 1k ohm R3 for creating a body zapper with pennies,
1 resistor for R2 see Fredbuster's PDFfile for specific resistor for frequency. I usevariable potentiometers because I like to set exact frequencies myself. I use100k potentiometers, they give me a range from 6hz to460hz when adjusting. You can see in the below photo I have both the largeaudio and micro potentiometers. The micro is used to be set at 15hz and the Audio is for creating variable.
1 on/off switch for the battery
1 toggle switch for the switching between 15hzand variable. That's how I like to do mine.
1 555CN timer chip, make sure it's the one that can handle up to18 volts. The CMOS 555 can only handle low voltage and is easily shorted out.
1 8 pin IC Socket, just incase you burn out your 555 you canreplace it without creating another circuit.
2 9 volt battery plugs, I like 2 because it lasts longer and hasmore amperage. One will do fin though.
Black and Red 22 gauge connecting wire, Make sure its the one with multiple threads of copper and not a solidone. Its easier to bend and move. The solid copperconnecting wire is to kinky and breaks to easily, formy taste.
1 spool of Solder, The thinner the better, for gettinginto tight spaces and heats up better.
1 Solder Iron, A pin point will be needed for this circuit.
1 1/8' audio phone jack, I like them because they make thebox look clean and it's and easy size to attach to any other devices.
Also see Fred's PDF specific info on goods.
First we take the PC board that was included with the Black boxand break it into a size we need.
Next we place the 8 pin bracket in the middle.
Notice on the back how I bend over the pins to hold it in place.
Next we attach R1 3.3k resistor. One end goes to pin 8 and theother to pin 7, I bend the legs over the pin then cut off 1/4' longer thanthe distance to the pin. the remaining 1/4' Ibent over and stick in the pin hole. see schematic.
Here is how it looks on the back.
Next we attach Compositor C2 1.0 mf, and Compositor C1 0.001 mf.C2 connects to pin 6 and the base of C1. C1 connects to pin 5 and C2 base.
Here is how it looks on the back, notice how the base of C1 andC2 are twisted together.
Next we add R4 3.9k and R5 4.7k to the board.
Notice on the back the ends are twisted together and connectedto Pin 3.
What you will need:
1 Project box with PC board included,
1 Compositor 1 micro farad, C2, I like the un-polarized becauseit allows you not to worry about positive an negativesides. If you do get one with a longer leg that's the positive, see schematicfor proper placement.
1 Compositor .01 micro farad, C1
1 LED 1-3 volt, small red ones. Remember the longerleg is the positive, connect properly,
1 Resistor 3.3k ohm, R1, It will say it on the upper partfiguring out the colors is a pain. See photo below for product ID.
1 Resistor 3.9k ohm R4
432 Hz Generator
1 Resistor 4.7k ohm R5
1 Resistor 1k ohm R3 for creating a body zapper with pennies,
1 resistor for R2 see Fredbuster's PDFfile for specific resistor for frequency. I usevariable potentiometers because I like to set exact frequencies myself. I use100k potentiometers, they give me a range from 6hz to460hz when adjusting. You can see in the below photo I have both the largeaudio and micro potentiometers. The micro is used to be set at 15hz and the Audio is for creating variable.
1 on/off switch for the battery
1 toggle switch for the switching between 15hzand variable. That's how I like to do mine.
1 555CN timer chip, make sure it's the one that can handle up to18 volts. The CMOS 555 can only handle low voltage and is easily shorted out.
1 8 pin IC Socket, just incase you burn out your 555 you canreplace it without creating another circuit.
2 9 volt battery plugs, I like 2 because it lasts longer and hasmore amperage. One will do fin though.
Black and Red 22 gauge connecting wire, Make sure its the one with multiple threads of copper and not a solidone. Its easier to bend and move. The solid copperconnecting wire is to kinky and breaks to easily, formy taste.
1 spool of Solder, The thinner the better, for gettinginto tight spaces and heats up better.
1 Solder Iron, A pin point will be needed for this circuit.
1 1/8' audio phone jack, I like them because they make thebox look clean and it's and easy size to attach to any other devices.
Also see Fred's PDF specific info on goods.
First we take the PC board that was included with the Black boxand break it into a size we need.
Next we place the 8 pin bracket in the middle.
Notice on the back how I bend over the pins to hold it in place.
Next we attach R1 3.3k resistor. One end goes to pin 8 and theother to pin 7, I bend the legs over the pin then cut off 1/4' longer thanthe distance to the pin. the remaining 1/4' Ibent over and stick in the pin hole. see schematic.
Here is how it looks on the back.
Next we attach Compositor C2 1.0 mf, and Compositor C1 0.001 mf.C2 connects to pin 6 and the base of C1. C1 connects to pin 5 and C2 base.
Here is how it looks on the back, notice how the base of C1 andC2 are twisted together.
Next we add R4 3.9k and R5 4.7k to the board.
Notice on the back the ends are twisted together and connectedto Pin 3.
Here is when I added the 555 timer, make sure the black dot isin the upper left corner.
Using one of the wire ends I cut off from the excess of theresistors I connect Pin 2 to Pin 6. like so.
Now is when I start adding the wires to hook up the positive andnegative connections.
Back of circuit.
Now for the wires that hook up to LED, Output jack and switches.
You can see how I soldered the connections together. Make sureyou are clean and accurate. Other wise a lose connection or overlapping solderwill cause the circuit not to work. This takes patients and time, don't rushit. If you do overlap a connection with solder, heat it up, use another wire tosuck up the excess and then use a knife to remove the last bits. I heat thewires first then add the solder. It's cleaner once you get used to soldering.Takes practice.
Here is what the final circuit looks like before it's place in a box. You can see the R2 I added here. I usea toggle switch to go back and forth between the set resistor and variableresistor. One end of the resistor is connected to R1 where it attaches to pin7. The middle Pin on the Potentiometer is then connected to a toggle switch.The Middle switch pin is then connected to C2 where it attaches to pin 6. Usingpotentiometers allows you to set a frequency you want. In Fredbusterstutorial he gives you the specific resistor for specific frequency.
Here are links to four photos showing detailed enlargement ofthe circuit with the variable potentiometers added and how they are connected.This should explain how I connected the potentiometers.
http://www.ryanmcginty.com/orgone/frontcircuitlg.jpg
http://www.ryanmcginty.com/orgone/backcircuitlg.jpg
http://www.ryanmcginty.com/orgone/beforeboxback.jpg
http://www.ryanmcginty.com/orgone/beforebox.jpg
Next I begin placing the circuit into the box. I slip the LEDwires thru to the outside because that's how you hook up this specific light. Iused shrink tubing to seal the connection keeping them not from touching otherwires.
You can see how I drilled the holes to fit each switch, LED andoutput jack. This is how I have the circuit placed inside the box. Notice theblank area to hold the two 9 volt batteries. I prefer two 9v because it allow the Freq Gen to run longer. About 14 days nonstop at 15hz.
And finally how the frequency box looks when finished. Notice I don't havepenny electrodes because this box is only to power OR devices and not kill bodyparasites. Copy the circuit drawing above and you can have both.
Radioshack sells a digital voltage meter which has asetting for frequencies. It cost me about $50. It works great. All I do isconnect the output from the generator to the meter's input wires. Instantly itsays the exact frequency the dial is tuned too. If you don't have voltage meterand work around the house repairing things yourself this is a must have.
To put the set the frequencies I use my computer. I use the1/8' stereo jack into my sound card, making sure the input volume is onlow. Use a Sound generator program and match the tones. Make sure the soundwave is set to square. It takes time to get it right but it works.
On a good day it takes me 1 hour and half to make the wholething. It will cost you about $40 to 45 in parts to make one like mine.
Good luck and have fun,
Ryan
With help from CBSWORK I have been testing music notes to chakras and the colors related. He informed me of using atone with sending energy. High C being a great tool againstattacking entities. Doing some research with frequencies set to specifictones has produced interesting results.
First here is a scale I found that translates music notes intohertz.
Click here for easier reading on the scales and frequency. http://www.angelfire.com/in2/yala/4scales.htm
This scale corresponds the best withthe chakras from others.
Calculation for Equal-Tempered tuning [A3 = 440Hz]
Octave0Octave1 Octave2 Octave3 Octave4 Octave5
0 A 55.000-110.000-220.000-440.000-880.000-1,760.000
1 A#/Bb 58.270-116.541-233.082-466.164-932.328-1,864.655
2 B 61.735-123.471-246.942-493.883-987.767-1,975.533
3 C 65.406-130.813-261.626-523.251-1,046.502-2,093.005
4 C#/Db 69.296-138.591-277.183-554.365-1,108.731-2,217.461
5 D 73.416-146.832-293.665-587.330-1,174.659-2,349.318
6 D#/Eb77.782-155.563-311.127-622.254-1,244.508-2,489.016
7 E 82.407-164.814-329.628-659.255-1,318.510-2,637.020
8 F 87.307-174.614-349.228-698.456-1,396.913-2,793.826
9 F#/Gb92.499-184.997-369.994-739.989-1,479.978-2,959.955 Hyperdock 1 8 0 1.
10 G 97.999-195.998-391.995-783.991-1,567.982-3,135.963
Screenshot plus mac. 11 G#/Ab103.826-207.652-415.305-830.61-1,661.21-3,322.438
12 A 110.000-220.000-440.000-880.000-1,760.000-3,520.000
The colors and chakras info Igot from: Color Medicine; by Charles Klotche. It'sloaded with great info on alot of stuff. Great reference book.
Music notes to color and chakras:
Red: Root Chakra note G
Orange: Sacral Chakra note A http://kwmxyn.xtgem.com/Blog/__xtblog_entry/19076688-convertisseur-avi-mp4-mac-gratuit#xt_blog.
Yellow: Solar Plexus Chakra note A#/Bb
432 Hz Music
Green: Heart Chakra note C
432 Hz Tone Generator
Blue: Throat Chakra note D
Indigo: Third Eye Chakra note D#
432 Hz Music Youtube
Violet: Crown Chakra note E
For placing specific music notes into OR devices I used a simple$20 chromatic tuner. I attached a lead off from the speaker to connect adevice. You can use alligator clips to connect to your PW or SP. There are alsotuners with built in audio outlets for the same price. I had to calibrate itusing a computer tone generator. Typed in the specific hertz for the tone thenadjusted the setting on the tuner to match. Mine was off by 4hz.
